Adsense

Ads

Saturday, March 7, 2015

ADJUSTMENTS OF INKING AND DAMPENING ROLLERS GTO 52


Klik gambar untuk memperbesar

Are made in the normal manner by inserting two strips of paper, each 1/10 mm (.004”) thick and 5 cm (2”) wide, between any ruber roller and its adjacent steel roller end. The adjusting screws are always located at the operator’s and drive side of the press. The settengs must be identical on both sides.

a)      Ink vibrator roller No. 14 towards asclillating steel roller No. 13 : undo lock nut, adjust hexagon bolt (ill. 24/5), tighten lock nut after adjustment has been completed.

b)      Distributor roller No. 12 towards both adjacent steel rollers No. 13 and 11 : adjustment by means of thumb-screws (ill. 22/2)


c)       Distributor roller No. 10 towards both adjacent steel rollers No. 9 and 11 : adjustment by means of thumb screw as mentioned under b) with roller No. 12

d)      Form inking roller No. 1 : the adjusment of each form inking roller is combined in one adjusting mechanism at the operator’s and drive side of ther press. The countersunk screw marked by white paint adjust the form roller towards the plate, the second countersunk screw without a paint mark permits adjustment of the form inking roller towards its oscillating steel roller (ill. 22/5 shows the adjustment of form inking roller No. 1)

e)      Form inking roller No. 2 : adjusting mechanism on ill. 22/6. Both form inking rollers, i.e. No. 1 and 2, are adjusted from the feeder side of the press.

f)       Form inking roller No. 3 : adjusting mechanism on ill.24/7

g)      Form inking roller No. 4 : adjusting mechanism on ill. 24/8. Both form inking rollers, No. 3 and 4, are adjusted from the delivery side of the press.

h)      Dampening vibrator No. 20 againist steel oscillator No. 19 : adjustment by means of adjusting screw with lock nut (ill. 23/5). Here, the steel gauges delivered with the press are used instead of paper strips. Please see to it that the dampening vibrator roller touches the oscillating dampening roller with very light pressure only since you will otherwise encounter water transfer problems.

i)        Form dampening roller No. 17 againist steel rider No. 19 : adjust countersunk screw (ill. 23/6) by means of long screwdriver delivered with the press; adjustment towards the plate by the adjusting screw (ill. 23/7) but only while press is running. The setting is correct, if you notice a light roller bounce when the roller passes over the plate cylinder gap.

j)        Form dampening roller No. 16 towards plate : by means of knurled adjusting screw (ill. 23/8) the bouncing action is checked as with the upper dampening form roller.

k)      The removable dampening steel rider can be inserted, after tha supporting brackets (ill. 23/8) have been retracted by the lever (ill. 23/9) on operator’s and drive side. Once the levers (ill. 24/9) are swung back towards the dampening unit, the steel rider will be automatically adjusted by means of spring tension againist both plate dampening rollers. No other adjustment is necessary. If you want to disconnect the dampening form rollers on a particular printing unit off the plate, you can do so by means of the dampening roller locks (ill. 23/12) on operator’s and drive side of the press. Once the locks are in operation and the press is printing, the dampening form rollers in that particular dampening unit are not touching the plate.



Ink duct

After releasing both star handles (ill. 17/6) the ink duct can be swung away for easy cleaning. In order to prevent scoring between the ink fountain roller and the side plates of the ink duct the grease groove has to be filled with grease after cleaning the ink duct.


For accurat ink feed setting the ink duct is provided with 16 screws (ill. 24/9). A ratchet (ill. 24/11) on operator’s side and drive side allows to turn the duct by hand. The dampening fountain roller is equipped with one ratchet (ill. 23/11).

Klik gambar untuk memperbesar


By : Berkah Mandiri Mesindo

1 comment:

  1. Click numpang lapak gan

    Trijaya anugrah sejahtera

    Menjual berbagai macam ISO Profile 99% Rwh,chemical printing productions,fountain blessing red, fountain bless yellow, fountain bless blue, fountain bless Exo Green,sparepart gun plate cleaner,tim plate, developer positif,IPA alkohol,corector(image remover),powder dry up(osaki), powder micron,blanket,plate offset,dll harga bisa di negosiasi dan kualitas sama ,untuk informasi lebih lanjut bisa menghubungi saya :
    Tommy via email (Tommy.transcal@gmail.com) atau WhatsApp (081310849918) terima kasih😀😀

    ReplyDelete

Note: Only a member of this blog may post a comment.